Remove the strut from the vehicle and install in a strut spring compressor. Drain the cooling system into a clean container for reuse. If the lobes and journals appear intact, place the front and rear journals in V-blocks and rest a dial indicator on the center journal. When removing the seat, be careful when setting on floor not to drop. Close the end of the bag and swish the cleaning fluid around, making certain the entire gasket has been thoroughly saturated. Lubricate with new engine oil as shown. Reconnect the negative battery cable and enter the radio security code.
Remove or disconnect the following: Negative battery cable Fuel pump Fuel filter carrier A Fuel filter Page 68 Back to Top Fig. The Transmission Number is on a label on top of the transmission. Tighten the pivot bolt of the idler pulley bracket, then tighten the locknut of the adjusting bolt. Loosen the pivot bolt of the idler pulley bracket, then loosen the locknut of the slotted adjusting mounting plate. Tighten the bolts to 28 ft. They tires of the same size and load range should be suitable for most winter as the original tires.
Transmission Checking Fluid Level, Vehicle Identification Number. Remove the knee bolster bolts and the knee bolster. Install the lower and middle timing covers. To adjust the steering wheel upward or downward: 1. The crankshaft pulley has a 50mm hexagon shape cast into the pulley that allows a tool to be used to hold the pulley in order to remove the bolt Fig. Adjust the Front Seats For safety, locking the doors reduces The following pages provide the chance that a passenger, instructions on how to properly especiall y a child, will open a door while the vehicle is moving and protect the driver and other adult occupants.
Remove the modular unit mounting bolts. Do not allow fuel spray or vapors to come in contact with a spark, open flame, or excessive heat a hot drop light, for example. Page 56 Back to Top 3. Page 22 Back to Top Fig. Remove the camshaft holder bolts 2 turns at a time in the sequence shown.
Before servicing the vehicle, refer to the Precautions Section. Remove or disconnect the following: Left front mount and bracket Right front mount and bracket Rear mount bracket through bolt Upper bracket Transaxle mount and bracket 13. Always wear safety goggles when working with, or around, the air bag system. Lower the vehicle to the ground 24. Install the pump and sprocket loosely. Rotate the crankshaft 180 degrees clockwise and recheck No.
Install the dipstick and breather hose. This is certainly considered as the safest. As benefits, there is not going to be considerable trouble and even breakage since you have misused the car. After installation, operate the control panel controls to make sure they work properly. Remove the center instrument panel lower cover screws and disengage the clips on the upper left side; then, disconnect the electrical connectors and remove the cover. Hold the crankshaft pulley with holder handle A and holder attachment B , then use a 19mm socket C and breaker bar to remove the bolt To install: 1. Failure to follow the safety precautions and the disarming procedure could result in accidental air bag deployment, possible injury and unnecessary system repairs.
Identification of some of the front suspension components 2002-06 Models 1. It really is not a shock to know that additional persons are endeavoring to discover the manual book both on the internet or offline. The offline edition, or real book, is usually integrated in to the package for every obtain. Set the timing marks as shown in the illustration with N0. Remove the strut from the vehicle and install in a strut spring compressor. Install or connect the following: Fuel filter Fuel lines.
Place the cover upright in a clean, protected area. Remove or disconnect the following: Negative battery cable Spark plug wires Distributor Valve cover Accessory drive belts Front cover Page 50 Timing belt. Check the wheel alignment and adjust as necessary. To activate the lockable retractor, 4. Keep the receipts for all work done on your vehicle. Always keep fingers, hands and objects clear of the cooling fans as unexpected operation of the cooling fans could cause physical injury. See the illustration for the torque sequence.
Check that all tubes, hoses, and connectors are installed correctly. Start the engine and check for leaks. Lubricate with new engine oil 2. In the final step, tighten all bolts, in sequence, to 7. When reinstalling, use a new cotter key Fig. Remove or disconnect the following: Negative battery cable Air bag and steering wheel Front wheels Driver-s side dashboard lower cover and undercover Air cleaner housing Steering joint bolts Tie rod ends Steering hoses Left side flange bolts Mounting brackets 4.
Exploded view of the radiator, fans and related components To install: 1. Turn the crankshaft counterclockwise to compress the auto-tensioner. Before servicing the vehicle, refer to the Precautions Section. Pull the strap to release the seat Put the head restraint behind the 3. Remove the upper radiator hose and lower radiator hose. Press the lower ball joint out of the steering knuckle.