I found one fuse blown just by checking each one and replaced it but that didn't work. Insert a tool or screwdriver into the access hole to override the brake-shift interlock. If your vehicle is involved in an accident or if you have problems fixing the alignment of your headlamps, have them checked by a qualified service technician. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool. Passenger side temperature control: Controls the temperature on the passenger side of the vehicle when in dual zone mode. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Be sure the belt webbing is not twisted. Connect the other end of the positive + cable to the positive + terminal of the assisting battery. Opening the liftgate window Press to unlatch the liftgate window. Do not exceed the Ford Motor Company recommended pressure even if it is less than the maximum pressure allowed for the tire. When towing, trailer tongue load or king pin weight is also part of cargo weight.
Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. Do not connect the end of the second cable to the negative - terminal of the battery to be jumped. If there is difficulty in turning the key, rotate the steering wheel until the key turns freely. . Fill the fuel tank completely and record the initial odometer reading in kilometers or miles. Electrical components such as your map light, radio, heated seats, high beams, power windows all have fuses and if they suddenly stop working, chances are you have a fuse that has blown out. Routine maintenance of the Personal Safety System is not required.
Some Fords have multiple interior fuse boxes including in the trunk - the video above will show you where the interior fuse box of your 2004 Explorer is located. Step 3 Remove plastic cover on the left side of the throttle body. This picture 2004 Ford Explorer Fuse Box Location. Turn the wrench counterclockwise until the tire is lowered to the ground and the cable has slack. Unnecessary shifting of this type could result in reduced fuel economy. Do not tow with a slingbelt. Remove the jack and fully tighten the lug nuts in the order shown.
Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. Allow the safety belt to retract to remove any slack in the belt. To set the parking brake, press the parking brake pedal down until the pedal stops. Press down on the top outboard area of the seatback until a click is heard. If this warning stays on, contact your dealer as soon as possible. Pull upward on the release handle to cycle the seats to the load-floor position. Pull back the slider panel on the seatback to release the closeout panel.
Make sure the tongue is securely fastened in the buckle. If your Explorer has many options like a sunroof, navigation, heated seats, etc, the more fuses it has. Temperature control: Determines temperature levels. Note: The doors will lock again, the horn will chirp and the lamps flash once. Note: Use a 4 mm socket or box wrench to turn the vertical adjuster control. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1—800—521—4140.
Always latch the vehicle seat to the floor, whether the seat is occupied or empty. Contact your local Ford dealership for assistance in proper trailer tow wiring installation. Ford Sport Tracs, because of their unique nature, require additional assembly procedures to install the side rails. The indicator light on the instrument cluster will turn on. To open, lift the release handle and the lid.
I really just wanted a chart to show which fuse it would be so that I could see if it's the fuse or something else Well if a fuse blown its because a high load or short circuit, tell me which fuses were blown number amperes and location and I ll pull out an schematic to see which circuit are feeding. I Have A 2004 Ford Explorer 4. Remove the access plug with a flat head screwdriver or similar tool. When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel. I got my code and had it working from his directions in 3 minutes.
Press and hold the two outside buttons releasing only when the red light begins to flash after 20 seconds. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Reverse steps to reinstall bulb s. Automotive Wiring Diagrams throughout 2004 Explorer Fuse Box Location by admin 2009 Ford Explorer Fuse Box Diagram — Vehiclepad 1994 Ford with 2004 Explorer Fuse Box Location by admin 2002 Ford Explorer Fuse Box Location.
Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. If you do then the diagram is in the thick manual that came with the truck. Auxiliary system if equipped Your vehicle may be equipped with auxiliary climate controls. Your Audiophile radio comes equipped with Satellite ready capability. Modifications to the front end of the vehicle, including frame,.